Peavey PV 1500 Power Amp

Add a 3,800W PV 3800 amp to your Bi-Pack system for a tri-amped system! The highest-power PV Series power amp utilizes a crossover specially tailored for subwoofers and the high power necessary to drive them. Load Fault Correction circuitry along with the famous DDT™ speaker protection and Turn On/Turn Off protection allow operation with greater efficiency, even under difficult loads and power conditions. The PV 3800 connects to a PV 1600 Bi-Pack through a simple 1/4" or XLR cable.

Peavey PV 3800 Power Amplifier Features:
2-channel power amp with DDT protection
Turn On/Turn Off protection
Load Fault Correction
1300 W/ch @ 4 ohms
775 W/ch @ 8 ohms
2650 W bridged @ 8 ohms
Twin temperature-dependant, variable-speed fans
 

Peavey IPR 3000 Power Amp

2-channel power amp delivers 1000W at 4 Ohms, 1500W at 2 Ohms per channel.
 
The Peavey IPR 3000 features two channels with independent, 100Hz crossovers and produces 530W per channel at 8 Ohms, or 800W per channel at 2 Ohms. Peavey's exclusive DDT speaker protection with multipoint clip sampling leads a protection-circuitry suite that also includes DC, Temp, Signal, and Active safeguards, all referenced on the front panel with LED indicators. The power amp also features a variable-speed fan housed in a lightweight aluminum chassis.

Peavey IPR 3000 Power Amp Features:
Class D topology
Two independent channels with 100Hz crossovers
Combi 1/4" & XLR inputs
Neutrik Speakon combo 1/4" outputs
DDT speaker protection with multi-point clip sampling
DC, Temp, Signal, and Active safeguards
LED indicators
Lightweight aluminum chassis
Variable-speed fan

Peavey IPR 1600 Power Amp

2-channel power amp delivers 530W at 4 Ohms, 800W at 2 Ohms per channel.

Same as IPR 3000

Peavey PV 2600 Power Amp

The Peavey PV 2600 Power Amp is a 2u rackmount unit. 2 x 900W RMS @ 4 ohms, 540W RMS @ 8 ohms, or 1800W RMS bridged mono. XLR, 1/4" and barrier strip inputs with DDT compression system, binding post and Speakon output connectors.

Peavey PV 2600 Power Amp Specifications:
Stereo Mode: 4 Ohms: 900 Watts RMS x 2
Stereo Mode: 8 Ohms: 540 Watts RMS x 2
Bridge Mode-Mono: 8 Ohms: 1800 Watts RMS
Total Harmonic Distortion: Less than 0.03% 20 Hz to 20 K, 10 dB below rated power in stereo mode both channels driven
Inputs: XLR, 1/4 inch and barrier strip
Detented input gain control
Binding post and Speakon output connectors
Separate Speakon mono bridge output
Mode switch for stereo or bridge operation
Low-cut filter switch for 40 Hz low cut filter
Thru/low output jacks and high output jacks
LED indicators for input signal, DDT and power
Peavey's famous DDT compression system
Frequency Response: 20 Hz to 20 kHz
Damping Factor: greater than 300
Hum and Noise: 100 dB
Rack Spaces: 2 RU

Peavey PV 1500 Power Amp

The Peavey PV 1500 Power Amp features Peavey's patented DDT distortion detection technique that virtually eliminates distortion. It also features Peavey's patented V-cooling design, which cools the power transistors more evenly than traditional heat-sink designs. 2-rackspace chassis.

Peavey PV 1500 Power Amp Specifications:
Stereo Mode: 4 ohms: 500W RMS x 2
Stereo Mode: 8 ohms: 300W RMS x 2
Bridge Mode-Mono: 8 ohms: 1000W RMS
Inputs: XLR, 1/4 inch and barrier strip
Detented input gain control
Binding post and Speakon output connectors
Separate Speakon mono bridge output
Mode switch for stereo or bridge operation
Low-cut filter switch for 40Hz low cut filter
Thru/low output jacks and high output jacks
LED indicators for input signal, DDT and power
Peavey's famous DDT compression system
Total Harmonic Distortion: Less than 0.03% 20Hz to 20kHz, 10dB below rated power in stereo mode both channels driven
Frequency Response: 20Hz to 20kHz
Damping Factor: greater than 300
Hum and Noise: 100dB
Rackspaces: 2U

Peavey PV 900 Power Amp

The Peavey PV 900 Power Amp delivers 300 watts per side @ 4 ohms and 450 watts @ 2 ohms. It features Peavey's patented DDT compression system and detented input gain controls, and less than 0.03% distortion. A real workhorse!

Peavey PV 900 Power Amp Specifications:
Stereo Mode: 4 ohms: 300 Watts RMS x 2
Stereo Mode: 8 ohms: 180 Watts RMS x 2
Bridge Mode-Mono: 8 ohms: 600 Watts RMS
Total Harmonic Distortion: Less than 0.03% 20Hz to 20kHz stereo mode both channels driven 10% below rated power
Inputs: XLR, 1/4 inch, and barrier strip
Detented input gain control
Binding post and Speakon output connectors
Separate Speakon mono bridge output
Mode switch for stereo or bridge operation
Low-cut filter switch for 40Hz low-cut filter
Thru/low output jacks and high output jacks
LED indicators for input signal, DDT9TM, & power
Peavey's famous DDT compression system
Frequency Response: 20Hz-20kHz
Damping Factor: greater than 300
Hum and Noise: 100dB
Rack Spaces: 2U

Peavey IPR DSP 1600 Power Amp with DSP

Part of Peavey's IPR Series, the IPR DSP 1600 Power Amp utilizes an advanced design that allowed Peavey engineers to dramatically reduce weight while increasing output power, reliability, and thermal efficiency. The rackmount power amp features two channels with independent, 100Hz crossovers and produces 530W per channel at 8 Ohms, or 800W per channel at 2 Ohms. It also has built-in, 32-bit, floating-point digital signal processing, and program-specific EQ presets that make common sound-reinforcement EQ treatments easy to perform, as well as delays, crossover, and stereo/mono operation with lockable security settings. A front-panel LCD screen allows users to quickly identify and assign presets. Like the rest of the Peavey IPR series, it has a resonant switch-mode power supply and a high-speed class D topology that yields the supremely high audio resolution and efficiency.

The IPR DSP 1600 also has Peavey's exclusive DDT speaker protection with multi-point clip sampling which leads a protection-circuitry suite that also includes DC, Temp, Signal, and Active safeguards. The IPR DSP 1600 power amp has a variable-speed fan housed in a lightweight aluminum chassis.

Peavey IPR DSP 1600 Power Amp with DSP Features:
Class D topology
Two independent channels with 100Hz crossovers
Combi 1/4" & XLR and barrier inputs
Neutrik Speakon and banana outputs
DDT speaker protection with multi-point clip sampling
Onboard DSP section with delay, EQ, assignable independent crossovers, setup wizard, lockable security settings
DC, Temp, Signal, and Active safeguards
LED indicators
Lightweight aluminum chassis
Variable-speed fan

Peavey CS 800X4 Power Amplifier

The CS Series is the global standard bearer for workhorse reliability. These amps benefit from Peavey's most popular audio innovations, including exclusive DDT compression/anticlipping protection. Circuitry protects against shorts, improper loads, abrupt turn-on levels, high temperatures, and subsonic frequencies that could damage loudspeakers. All CS power amps include toroidal power transistors for lighter weight and increased power.

Peavey CS 800X4 Power Amplifier Specifications:
Power ratings:
825W, 4 ohms bridged
500W, 1 x 2 ohms
350W, 1 x 4 ohms
200W, 1 x 8 ohms
400W per channel, 4 x 2 ohms
300W per channel, 4 x 4 ohms
180W per channel, 4 x 8 ohms
Frequency response: 10Hz-20kHz
Size: 2RU (Dual rackspace)
38 lbs.

Peavey CS 4000 Power Amplifier

The Peavey CS Series Amplifiers are the global standard bearer for workhorse reliability. These rackmount amps benefit from Peavey's most popular audio innovations, including exclusive DDT compression/anticlipping protection. The CS 4000 circuitry protects against shorts, improper loads, abrupt turn-on levels, high temperatures, and subsonic frequencies that could damage loudspeakers. All CS power amps include toroidal power transistors for lighter weight and increased power.

Peavey CS 4000 Power Amplifier Specifications:
Power ratings:
4000W, 4 ohms bridged
2550W, 1 x 2 ohms
1600W, 1 x 4 ohms
900W, 1 x 8 ohms
2000W per channel, 2 x 2 ohms
1350W per channel, 2 x 4 ohms
800W per channel, 2 x 8 ohms
Frequency response: 10Hz-100kHz
Size: 2RU (Dual rackspace)
43 lbs.

Peavey CS 3000 Power Amplifier

The CS Series is the global standard bearer for workhorse reliability. These amps have benefitted from Peavey's most popular audio innovations, including exclusive DDT compression/anticlipping protection. Circuitry protects against shorts, improper loads, abrupt turn-on levels, high temperatures, and subsonic frequencies that could damage loudspeakers. All CS power amps include toroidal power transistors for lighter weight and increased power.

Peavey CS 3000 Power Amplifier Specifications:
Power ratings:
3050W, 4 ohms bridged
2000W, 1 x 2 ohms
1275W, 1 x 4 ohms
750W, 1 x 8 ohms
1500W per channel, 2 x 2 ohms
1025W per channel, 2 x 4 ohms
650W per channel, 2 x 8 ohms
Frequency response: 10Hz-100kHz
Size: 2RU (Dual rackspace)
40 lbs.

Peavey CS 4080HZ Power Amplifier

The CS Series is the global standard bearer for workhorse reliability. These amps benefit from Peavey's most popular audio innovations, including exclusive DDT compression/anticlipping protection. Circuitry protects against shorts, improper loads, abrupt turn-on levels, high temperatures, and subsonic frequencies that could damage loudspeakers. All CS power amps include toroidal power transistors for lighter weight and increased power.

Peavey CS 4080HZ Power Amplifier Specifications:
Power ratings:
4080W, 4 ohms bridged
2450W, 1 x 4 ohms
1400W, 1 x 8 ohms
2040W, 2 x 4 ohms
1250W per channel, 2 x 8 ohms
Frequency response: 10Hz-100kHz
Size: 2RU (Dual rackspace)
43 lbs.

Peavey CS 2000 Power Amplifier

The CS Series is the global standard bearer for workhorse reliability. These amps benefit from Peavey's most popular audio innovations, including exclusive DDT compression/anticlipping protection. Circuitry to protect against shorts, improper loads, abrupt turn-on levels, high temperatures, and subsonic frequencies that could damage loudspeakers. All CS power amps include toroidal power transistors for lighter weight and increased power.

Peavey CS 2000 Power Amplifier Specifications:
Power ratings:
2150W, 4 ohms bridged
1200W, 1 x 2 ohms
830W, 1 x 4 ohms
515W, 1 x 8 ohms
1075W per channel, 2 x 2 ohms
760W per channel, 2 x 4 ohms
490W per channel, 2 x 8 ohms
Frequency response: 10Hz-25kHz
Size: 2RU (Dual rackspace)
36 lbs.

Peavey CS 1400 Power Amplifier

The Peavey CS Series amplifier is the global standard bearer for workhorse reliability. These amps benefit from Peavey's most popular audio innovations, including exclusive DDT compression/anticlipping protection. Circuitry to protect against shorts, improper loads, abrupt turn-on levels, high temperatures, and subsonic frequencies that could damage loudspeakers. All CS power amps include toroidal power transistors for lighter weight and increased power.

Peavey CS 1400 Power Amplifier Specifications:
Power ratings:
1400W, 4 ohms bridged
785W, 1 x 2 ohms
550W, 1 x 4 ohms
345W, 1 x 8 ohms
700W per channel, 2 x 2 ohms
500W per channel, 2 x 4 ohms
330W per channel, 2 x 8 ohms
Frequency response: 10Hz-25kHz
Size: 2RU (Dual rackspace)
33 lbs.

Yamaha P7000S Dual-Channel Power Amp

The Yamaha P7000S Dual-Channel Power Amp gives you clean power and low weight. The P-Series amps deliver pro-quality power in a wide range of configurations, and are perfect for mating with the popular Club Series speakers, as each model's power signal is tuned via YS processing to the needs of Club Series speakers. All models feature both XLR and 1/4" TRS inputs and Neutrik Speakon, phone plug, and 5-way binding post outputs. Other features include sweepable high and low pass filters, Yamaha's exclusive EEEngine technology for high performance with exceptional efficiency, and a variable speed fan. 2U chassis. Delivers 950W/ch @ 4 ohms, 700W @ 8 ohms, and 1,900W @ 8 ohms bridged.

Yamaha P7000S Dual-Channel Power Amp Features:
Pro-quality power in a wide range of configurations
Perfect tuned via YS processing for use with the popular Club Series speakers
Yamaha's exclusive EEEngine technology for high performance with exceptional efficiency
XLR and 1/4" TRS inputs
Neutrik Speakon, phone plug, and 5-way binding post outputs
Sweepable high and low pass filters
Variable speed fan
Delivers 2 x 700W @ 8 ohms, 2 x 950W @ 4 ohms, and 1,900W @ 8 ohms bridged

Yamaha P2000S Dual Channel Power Amp

Same as P7000s, except power

Yamaha P2000S Dual-Channel Power Amp Features:
Pro-quality power in a wide range of configurations
Perfect tuned via YS processing for use with the popular Club Series speakers
Yamaha's exclusive EEEngine technology for high performance with exceptional efficiency
XLR and 1/4" TRS inputs
Neutrik Speakon, phone plug, and 5-way binding post outputs
Sweepable high- and low-pass filters
Variable-speed fan
Delivers 2 x 500W @ 8 ohms, 2 x 700W @ 4 ohms, and 1,400W @ 8 ohms bridged

Yamaha P3500S Dual Channel Power Amp

Same as P7000s, except power

Yamaha P2000S Dual-Channel Power Amp Features:
Pro-quality power in a wide range of configurations
Perfect tuned via YS processing for use with the popular Club Series speakers
Yamaha's exclusive EEEngine technology for high performance with exceptional efficiency
XLR and 1/4" TRS inputs
Neutrik Speakon, phone plug, and 5-way binding post outputs
Sweepable high- and low-pass filters
Variable speed fan
Delivers 2 x 350W @ 8 ohms, 2 x 450W @ 4 ohms, and 900W @ 8 ohms bridged
 

Yamaha P5000S Dual Channel Power Amp

Same as P7000s, except power

Yamaha P5000S Dual Channel Power Amp Features:
Pro-quality power in a wide range of configurations
Perfect tuned via YS processing for use with the popular Club Series speakers
Yamaha's exclusive EEEngine technology for high performance with exceptional efficiency
XLR and 1/4" TRS inputs
Neutrik Speakon, phone plug, and 5-way binding post outputs
Sweepable high- and low-pass filters
Variable-speed fan
Delivers 2 x 500W @ 8 ohms, 2 x 700W @ 4 ohms, and 1,400W @ 8 ohms bridged